橋梁伸縮縫裝置施工視頻
GQF-E80型橋梁伸縮縫的現場安裝
將兩段伸縮縫裝置上平面置于同一水平面上，使兩段伸縮裝置接口處緊密靠攏，并校直找正。(2)用鋼絲刷清除浮銹，用石棉繩填塞到對接處的凹槽內，以防焊渣流入。(3)用的506焊條逐步焊接。(4)刷防銹漆。伸縮裝置的吊裝就位吊裝時應按照廠方表明的吊點位置起吊。安裝時，伸縮裝置的中心線應與梁端預智槽伸縮縫預留間隙中心線想重合（可用吊繩法找平），其長度與橋?qū)挾葘?duì)應，然后穿放橫向聯結水平鋼筋，并將邊梁墊起（不可懸空）。GQF-E80型橋梁伸縮縫的標高與固定,沿橋?qū)挋M向每隔1.2m放置一橫吊梁。使伸縮裝置上頂面緊密貼在槽鋼下面，以兩側瀝青混凝土面層的標高為準，控制伸縮縫的標高，然后對伸縮縫的縱向直線度也進行調整。伸縮縫的標高直線度調整到符合設計要求后，可進行臨時固定，固定時應沿橋?qū)挼囊欢讼蛄硪欢艘来螌⑸炜s縫邊梁上的錨固裝置與預留槽的預埋鋼筋每隔2-3個錨固筋骨焊一個焊點，兩側對稱施焊，以抄平后的伸縮縫不再發生變位，嚴禁從一端平移施焊，造成伸縮縫翹曲。
對E80型橋梁伸縮縫的焊接固定后應對伸縮縫的標高再復測一遍，確認在臨時固定過程中未出現任何變形、偏差后，把異型鋼梁上的錨固鋼筋與預埋鋼筋在兩側同時焊牢，好一次全部焊牢。如有困難，可先將一側焊牢。應特別注意，無論是臨時固定，還是后的終焊均不得在較大外力作用下或預埋與邊梁錨固鋼筋間隙大干1.5mm狀態下強行施焊，并遵循從橋?qū)挼囊欢讼蛄硪欢艘来魏附踊蛴蓸驅拑蛇呄驑驅捴行囊来魏附拥脑瓌t，絕不可由橋?qū)拑蛇呄驑驅捴行囊来魏附?，以免造成伸縮裝置的較大變形或標高的變化。在伸縮裝置的梁凹槽內漆一層潤滑油（液體蠟或黃油）加以保護。
衡水路翔公司為您提供Z型橋梁伸縮縫產品在橋梁上安裝時的步驟及注意事項：
Steps and precautions for installing Z-bridge expansion joint products on bridges:
1、當工程施工單位在安裝橋梁伸縮縫時，一旦發生碰撞變形，很難修復為合格產品，
When the construction unit is installing the bridge expansion joint, once the collision deformation occurs, it is difficult to repair it as a qualified product.
所以在安裝的全過程中，一定要采取措施保護，嚴禁任何車輛通過。
Therefore, in the whole process of installation, measures must be taken to protect and prohibit any vehicles from passing.
2、一定要精心操作。如果出現現場不易調整，所以對伸縮縫的成品檢查一定要認真、仔細。不合格不可運至現場。
Be careful. If the scene is difficult to adjust, the inspection of the finished product of the expansion joint must be careful and careful. Failure to pass shall not be shipped to the site.
3、在橋梁伸縮縫在安裝前，要與設計圖和現場核對位置、尺寸無誤后，再穩放入預留槽。
Before the bridge expansion joint is installed, it must be placed in the reserved slot after the design and the site check position and size are correct.
要將橋上各接縫處縫隙一定要用聚苯乙烯泡沫板塞嚴，防止?jié)沧⒈Ｗo(hù)帶混凝土?xí)r灌入，使縫失效。
The gap between the joints on the bridge must be tightly packed with polystyrene foam board to prevent the pouring of the concrete when pouring the protective belt, and the joint is invalidated.
同時，也不可將裝置內灌進混凝土，以免更換V形象膠帶時受阻。
At the same time, it is not possible to pour the device into the concrete to avoid being blocked when replacing the V-image tape.
4.、在保護帶混凝土澆筑后，前7-8日一定要及時灑水養護，以利強度增長和防止裂縫出現。
After the concrete is poured in the protective belt, the first 7-8 days must be sprinkled and maintained in time to increase the strength and prevent cracks.

查看全部介紹